Commissioning RBS 6000 2G RUS (Step by step)

http://www.mediafire.com/file/t6w0triktnu9uyb/Commisioning+RBS+6000+2G.xls

http://www.mediafire.com/file/aa84tqaxr6y7zi0/RBS6000+GSM+Commissioning+Guide.pdf

http://www.mediafire.com/file/qtxk9pg5k8j4pp4/Serial+Cable+pin-out+for+RBS+6000+DUG.pptx

Step by step commissioning RBS 6000 2G RUS

Tools

1) Laptop

2)  USB-serial cable + driver

3) Serial DB9-RJ45 cable

DB9

RJ45

2

3

3

2

5

1

4) Software OMT

Step by step for Commisioning RBS 6000 2G

1. Create IDB (Installation Database)

> Click menu Configuration-->Create IDB

Cabinet Setup

> Click "New"

> Select RBS cabinet type

> Select Power System

> Select in Climate System

Antenna Sector Setup

> Click "New"

> define number of sector

> Select  Frequency Band, GSM 900 (B0/B8) or GSM 1800 (B3)

> Select Rx Diversity (2-Way / 4-way)

> Select Antenna Sharing

> definenumber of RUS, adjust with number of RUS actual

>  definewhat RBS use TMA or NOT

> Click "RE Setup"

> Select Tipe RUS (RUS01/RUS02)

> Select Radio Mode (Single/Mixed)

> definenumber of TRx per sector

2. Change the view to "Cabinet 0", set the position of the modules in the RBS

> Click menu "Configuration-->define-->RU Position

> Determine the position of the shelf (shelf) and slot of each module

3. Define which modules we use in RBS (make sure the module we need is blue color, not lines)

> Click menu "Configuration-->define-->present RU

> Move the  modules that we need from the position of "not present" to "present"

4. Define maximum power RRUS

> Click menu "configuration-->define-->MCTR"

> Contact INOC for setting

5. Define Node parameter --> Depend on configuration (see the sheet MSSM)

6. Setup transmision configuration

> Click menu "configuration-->define-->transmission"

> Select STN equipment

> Select Network Topology : (Stand alone / cascade)

7. Define gps parameter (if the configuration are Mixed mode or Dual DUG (using GPS cable))

> Click menu "configuration-->define-->Gps parameters

> select GPS present " Yes"

8. Define Feeder and ESB Delay + TF Conpensation (if  the configuration is Antenna Sharing (using ESB cable) or MBC)

> Click menu "configuration-->define-->Feeder and ESB Delay

Define Feeder and ESB Delay

> Double click on ESB --> Add--> input data on  "delay(ns)"

> Click menu "configuration-->define--> TF Compensation

Define TF Compensation

> choose RBS GSM on Master RBS, input 17784 on master Transmitter chain delay, and input delay on ESB delay --> click appy

9. Define RBS Identity (optional)

> Click menu "configuration -->define--rbs identity

> Fill in RBS name and RBS description

11. Setup External alarm

> Click menu "configuration-->define-->alarm inlets"

> Select Hardware Unit = SAU

> Setup each alarm inlet

> inlet usage = external alarm

> type = closing (NO) / breaking (NC)

> ID

> Severity (level 1=critical, level 2=major)

> Comment = alarm name

12. Connect to RBS dan install IDB

> Click menu "RBS GSM-->Connect"

> Click menu "Configuration-->install IDB"

> Wait until finish

Note : When Install IDB (Configuration --> Install IDB)

make sure state of RBS is "Full Maintenance Mode" (Blue led lit steady)

How to change RBS:

> Select The view "system"

> Right click on GSM Node, and Select "Change Maintenance Mode"

> make sure Blue led lit steady